CSA Tire Inspection

 

VIDEO SUMMARY

The CSA Tire Inspection video starts with the now standard boilerplate legal disclaimers, followed by a musical intro of a turquoise blue Michelin truck, and self-introductions by Kevin Rolling, of the Tire Industry Association, and Doug Jones of Michelin, NA. At 2:45 there is an introduction to CSA (DOT’s regulatory enforcement methodology) and Capt. Douglas Shackelford (North Carolina State Highway Patrol) tells us he will talk about the “visual inspection components” to avoid inspections.

CSA created a new Safety Measurement System (SMS) for both driver and company. Under CSA, individual road violations are assigned a “severity rating” that ranges from one to ten, with ten being the most severe and the most likely to cause an accident.

Items that are required to be inspected under Part 393 for safe operation prior to each trip include:

– Lamps, Reflective Devices and Electrical Wiring
– Brakes
– Glazing & Window Construction
– Fuel Systems, including: Compressed Natural Gas Fuel Containers and Liquefied Petroleum Gas Systems
– Coupling Devices and Towing Methods
– Miscellaneous Parts and Accessories including: Tires, Windshield Wipers, and Rear Impact Guards
– Emergency Equipment
– Protection against shifting and falling cargo, including specific securement requirements by commodity type
– Frames, Cab and Body Components, Wheels, Steering and Suspension Systems

Capt. Shackelford, “For purposes of this video, we’re going to focus on tires. So let’s look at the federal regulations for tires.”

Feel the sidewalls for bulges and defects.

Feeling the sidewalls for bulges and defects.

Feeling the face or crown of the tire for damage: lay hand flat on tire and slide it across the face.

Feeling the face or crown of the tire for damage by laying hand flat on tire and sliding it across the face.

Tires Part 393.75: No motor vehicle can be operated if any tire exhibits the following conditions:

Exposed body ply
– Exposed body ply or belt material through the tread or side wall

tread separation

– Tread or sidewall separation
– Flat tire or a tire with an audible air leak

Cut in tire exposing the ply or belt.

– A cut where the ply or belt material is exposed

These are generally cited as Out-of-Service (OOS) conditions.

Triangular repair patch

Exception: An under 3/8 inch bulge on the sidewall, if accompanied by a blue repair triangle (no more than two repair patches) is acceptable. Use a “bulge gage” to measure the height of the bulge, if in doubt.

Lead tires (steering tires, converter dollies for semi-trailers and steer axles on full trailers ) must have at least 4/32s tread depth at any point on any major groove expect where tread wear indicators or stone ejectors are located. All other tires must have 2/32s inch in every major groove of the tire.

If tread depth is under the limit as established by Part 393.75, then the driver will be cited for a violation and assessed points under CSA. However, the vehicle will be placed out of service if the tread depth is below the limit set by the Commercial Vehicle Safety Alliance (CVSA).

OOS if two adjacent major grooves are under specs.

The vehicle is OOS, if tread depth is under specification at any two adjacent grooves.

Decoupler groove along the sidewall is not a major groove.

The decoupling groove at the shoulder is not a major groove. Other terms for this tire feature include: “shoulder wear protector” or “defense groove” or “pressure distribution groove,” depending on the manufacturer.

If a tire is out of specification, then this is a citable violation (ticket-able) but not an out-of-service (OOS) condition.

The decoupler groove along the shoulder is not a "major groove."

Insufficient tread in a decoupling groove is not a violation or an OOS condition, if all the major grooves have sufficient tread depth.

Irregular wear is not a violation or OOS condition.

Irregular wear (example: tire “cupping” from dry steering) is not a violation or an OOS condition, if all the major grooves have sufficient tread depth.

Missing chunks are not a violation if sufficient thread is found in every major groove.

Missing thread chunks are not a violation if sufficient thread is found in every major groove.

Missing tread chucks are not a violation or an OOS condition, if all the major grooves have sufficient tread depth and the missing tread material does not expose the ply materials.

Weather checking is not a violation or OOS condition, as long as underlying material is not exposed.

Weather checking is not a violation or an OOS condition, if the checking does not expose the underlying material.

Bus Restrictions:
FMCSR 393.75(4)(d) says, “No bus shall be operated with regrooved, recapped or retreaded tires on the front wheels.” This is an OOS condition.

A “regroovable” tire is allowed, but not a regrooved tire.

General Restrictions:
FMCSR 393.75(4)(d) says, “A regrooved tire with a load-carrying capacity equal to or greater than 4,920 pounds shall not be used on the front wheels of any truck or truck tractor.”

Almost all of these conditions carry a “severity rating” of eight points if found during a roadside inspection.

Example: a tire is found during a roadside inspection with less than 50% of inflation as marked on the sidewall. As such an OOS condition exists (as the tire is considered flat and may have sustained hidden “run-flat” damage).

Under CSA, eight points are given for the flat and two additional points for an OOS condition – multiplied three fold for the 0-6 months multiplier resulting an a total of thirty CSA points (the max allowed for any single violation within a CSA BASIC). This in turn, affects the fleet’s CSA “SMS score” and could later result in additional “targeted inspections.”

“Enforcement officers are now equipped with a valuable tool for any fleet we inspect. And since the CSA “Snapshot” is based on real time inspections and data, we know exactly where to look and have complete confidence when identifying violations, improving safety on our nation’s highways.”

Kevin Rolling, “Perform a thorough pretrip and posttrip inspection.”

Doug Jones: “Thanks for watching.”

ADDITIONAL NOTES:

The inspections performed by a US DOT certified roadside inspector under CVSA guidelines are focused on CRITICAL items. A driver has a duty to thoroughly inspect (and document) not just the aforementioned “critical items,” but all items (as specified by the regulations) on a vehicle and its load.

The “window of opportunity” is the period of time when a part or accessory begins to exhibit poor performance, prior to a repair being made. This is a period of time and/or of deteriorating performance when the part or freight is in a sub-critical condition that will require service or repair.

For example, when laying a hand flat on tire and sliding it across the face or crown of the tire, if one direction feels smooth and the other has sharp edges, then there is a lateral drag problem (edges of the tire are feathering away from the direction of the push), possibly due to excessive, unequal camber, resulting in decreased MPGs.

Irregular wear is an indicator of future trouble.

Irregular wear is an indicator of future trouble.

“Heavy, spotty, cupped or irregular tire wear
are signs of components (king pins, bushings, tie rod ends, steering gear, pitman arms, idler arm, spring sag, shock leakage, or wheel bearings) that are out of specification.”

Always try to always stay out of the tire’s trajectory areas and know when use a tire cage when working around tires. Several years ago, a small child was killed in Michigan watching his father inflate a truck tire.

Learning how to properly read a tire can prevent later breakdowns in critical items, saving time and money, honor and lives.

 

FINAL TIRE SAFETY WARNINGS

“Flat tires,” according to OSHA, are any tires under 20% of proper inflation. DO NOT re-inflate any flat tires unless you are a properly trained tire technician. Tires over 80 percent of the recom­mended pressure may be inflated on the vehicle if proper pre­cautions are taken. Flats should be properly inspected to find the cause of the leak. (See OSHA 29 CFR Part 1910.177)

Stay out of the tire's trajectory areas or use a tire cage when working around tires.

Stay out of the tire's trajectory areas and know when to use a tire cage when working around tires.

To learn how to win by conducting a professional inspection each time, every time, please visit: http://www.part380.com/si393.html

Do you know:

– cargo insurance policies will NOT cover losses due to bad load securement?

a driver can face criminal charges if someone is hurt or killed as the result of an unsecured load?

 

 

Leave a Reply